Skip to content. | Skip to navigation

Personal tools

Instrument structure

IMACS instrument structure fabrication - 11/28/2001 to 3/13/2002

The IMACS instrument structure was designed by Steve Gunnels of Paragon Engineering, and was fabricated by Martinez and Turek of Rialto, CA.

The instrument structure is composed of two large (100" dia) disks, which are connected to each other with a 10 element truss. The two disks are supported by the instrument carriage, which has rollers that allow the disks (and instrument) to rotate about the Nasmyth optical axis.

The Front Optical Support Structure disk (FOSS disk) carries three guide cameras, the slit-mask shuttle and transfer mechanisms, and the field lens. The Main Optical Support Structure (MOSS) carries the collimator, long camera, short camera,
disperser server, and filter changers.

The total bare structure weight is about 3100 lbs.

Status:

- The structure is currently on schedule for completion at the end of January, 2002.

- Feb 2, 2002 - We are now officially late, and hoping for completion by the end of February.

- Feb 18, 2002 - Looking good for delivery by the end of the month.

- Feb 28, 2002 - now planning for delivery on 3/6/02.

- Mar 7, 2002 - delivery (structure and forklift!) scheduled for 3/12/02.

- Mar 13, 2002 - structure was delivered and installed on the carriage today!

 


March 13, 2002 -- Delivery Day!

The M&T truck arrived at 10:30 AM on another wintery southern California morning...

1

The FOSS end of the structure mounted on the back of the truck.

2

The scene from the top of the shop building.

3

Structure on the truck, Steve Gunnels supervising the unloading...

4

Structure off the truck...

5

Structure on the ground...

6

The rental forklift comes in very handy...

7

Now off the palette...

8

View from the instrument carriage...

9

Stucture ready for the second lift...

10

The first set of wood blocks didn't work quite as planned...

11

Up on the second lift...

12

Headed into the shop - note the new, simpler blocks on the forklift forks...

13

Room to spare on the way in - 120" wide door, 100" dia structure...
Steve Gunnels supervising the installation.

14

Bigelow supports the structure while Gunnels prays for the bolts to fit...

15

Gunnels assembles the shop drive preload.

16

We hadn't figured it out yet, but the structure requires about a 6 lbs. load at the edge to rotate!

17

A happy PI surveys the optical axis...

18

The OA from the opposite direction.

19

The Mask transfer mechanism installed in about five minutes! Not a bad day's work...

20

 


 

March 7, 2002

 

Final assembly of the MOSS and mainframe is now in progress. The IMACS structure fits on a table in a small corner of the M&T facility...

21

The MOSS can be seen to the left, with the long camera mounting flange pointing up and to the right.

22

Tyson Hare, Steve Gunnels, and Steve Fox survey the structure.

23

The collimator mounting flange as seen from the field lens clearance hole.

24

 


March 4, 2002

A Hyster 13,000 lb. forklift available from Industry Lift, City of Industry, Ca. Fork opening, and fork left/right position are both hydraulically adjustable ($500 for one day with delivery).

25

 


February 28, 2002

The MOSS, now prime-painted, in its final machining operation - finishing of the bolting strips for the interface to the mainframe. Note the turnbuckles now in place for controlling the MOSS/mainframe interface at the top of the upper wing.

26

The mainframe, FOSS disc, showing final machining of guider and SMS mounting surfaces, and mounting holes.

27

Here are the tripod parts, ready for welding and bolting to the mainframe

28

The mainframe on a VTL, ready for welding of the tripod and mounting of the MOSS box.

29

 


 

February 18, 2002

 

The mainframe has been primer painted and is now undergoing final machining operations.

 

30

The only material being removed here is on the MOSS box mounting flanges. The VTL might not be the best machine for this job, but it was the one available!

31

The repaired DSS cut-out in the MOSS box. Note replaced material on the left side of the cut-out. The MOSS was re-stress-relieved following these changes.

32

Cut-out repair from the opposite side.

33

Bigelow makes a rare appearance (!) at Martinez and Turek (with the MOSS in the paint booth)...

34

 


February 12, 2002

The mainframe welding is now complete, and shown here following sand-blasting.
The mainframe is currently on a vertical turning lathe for final turning operations, and goes to a horizontal boring mill next for finishing.

35

 


Mainframe welding details. Vertical bar stock provides the mounting surfaces for the instrument enclosure panels.

36a36b

 


The MOSS has been modified to allow extra clearance around the DSS wheel.

The vertical tubes are temporary for fixturing.

 

37

 


Detail of the modified DSS cut-out. Steve, does this look right to you?

38

 


 

February 1, 2002

Steve Fox and Richard Vicario of M&T are fitting the diagonal truss elements between the FOSS (up) and MOSS (down) discs Steve is standing on most of the truss elements!
Welding of the truss should be finished by the 6th...

39

These are the doubler plates for stiffening the top wing of the MOSS. We will be enlarging the opening in the MOSS to allow for cross-dispersing prisms to be mounted on top of gratings in the disperser server.

40ÂÂÂ

January 18, 2002

The MOSS box is not just flat plates anymore... Richard Vicario and the MOSS.
The round tubes are temporary tooling.

41

Webs have been added to the stiffening rib at the bottom of the FOSS disk.

42

Details around the center hole and SMS hole in the FOSS disk.

43

The finished MOSS disk.

44

January 8, 2002

MOSS box plates ready for fit-up and welding

45

FOSS disc stiffener plate in lightening hole.

46

FOSS welding detail between slit-mask and center cut-outs.

47

FOSS disc welding partially completed

48

December 19, 2001

MOSS disc complete - Steve Fox, Dave Boese (M&T), and Alan Dressler shown for scale

49

Plates of the FOSS disc ready for welding

50

December 4, 2001

Dave Boese and Richard Vicario with the MOS disk.

51

12/04/01 - Richard Vicario welding a MOS face sheet to the rim.

52

12/04/01 - MOS welding details of stiffeners and internal webs.

53

11/28/01 - This image shows the laser-cut steel disks that will eventually form the Main Optical Structure Disk (MOS disk), which supports a smaller structure (the MOS) that carries the collimator, long camera, short camera, disperser server, and camera filter changers.

54

Document Actions